QuizPilot › Subjects › Muhandislik
Muhandislik

SET-A JUNIOR ENGINEER MECHANICAL 01-10-2023_0001 (2)

by Pompous · 130 questions · 0 saves
Play in QuizPilot
#1
If a spur gear has 30 teeth and is rotating at 200 rpm with a module of 2 mm, what would be its pitch line velocity in mm/s?
  1. 501 mm/s
  2. 3 mm/s
  3. 2 mm/s
  4. 1264 mm/s
Show answer
3 mm/s
#2
The rotational speed of an automobile engine fluctuates between 210 rad/sec and 190 rad/sec. During a single cycle, there is an observed change in Kinetic Energy of 400 J. What is the mass inertia of the flywheel about its central axis, represented in kg-m??
  1. 10
  2. 15
  3. 05
  4. 25
Show answer
10
#3
What is the most employed tooth profile in gear drives for power transmission?
  1. A hyperbola
  2. A spiral
  3. A cycloid
  4. An involute
Show answer
An involute
#4
Match List-I with List-II and select the correct answer using the correct answer using the codes given below: List - I
  1. Spur Gears
  2. Bevel Gears
  3. Worm Gears
  4. Helical Gears
Show answer
Helical Gears
#5
Transmit motion between parallel shafts. 3. Transmit motion between intersecting shafts. 4. Transmit motion between parallel shafts or non- parallel shafts Codes: a b c d
  1. 3 1 2 4
  2. 2 3 4 1
  3. 2 4 1 3
  4. 3 2 1 4
Show answer
2 4 1 3
#6
Match List-I with List-II and select the correct answer using the codes given below: List - I List - II
  1. Regulating 4. Center less wheel grinding
  2. Apron 2. Milling Machine
  3. Indexing 3. Shaper mechanism
  4. Quick return I. Lathe machine
Show answer
Indexing 3. Shaper mechanism
#7
Misruns and cold shuts in sand casting arise from:
  1. Lower pouring temperature
  2. Defective mold flask
  3. Elevated pouring temperature
  4. Diminished strength of solidified metal
Show answer
Lower pouring temperature
#8
Assertion-Reasoning: Assertion (A): Plastic deformation in metals and alloys is a permanent deformation under load. It is useful in strengthening the products obtained via cold rolling process. Reason (R): Plastic or permanent deformation in metal/alloys causes an increase in dislocation density.
  1. Both A and R are individually true, and R is the correct explanation of A.
  2. Both A and R are individually true, but R is NOT the correct explanation of A
  3. A is true but R is false.
  4. A is false but R is true.
Show answer
Both A and R are individually true, and R is the correct explanation of A.
#9
The volume of a cube with side 'i' and the volume of a sphere with radius 'r' are equal. Both the cube and sphere are composed of the same material and are being cast. What is the ratio of the solidification time of the cube to that of the sphere?
  1. $(\frac{4\pi}{6})^2 (\frac{r}{i})^2$
  2. $(\frac{4\pi}{6})^6 (\frac{r}{i})^6$
  3. $(\frac{4\pi}{6})^2 (\frac{r}{i})^3$
  4. $(\frac{4\pi}{6})^2 (\frac{r}{i})^4$
Show answer
$(\frac{4\pi}{6})^2 (\frac{r}{i})^2$
#10
In machining, width of cut becomes equal to depth of cut when the principal cutting edge angle is equal to:
  1. $90^\circ$
  2. $30^\circ$
  3. $0^\circ$
  4. $60^\circ$
Show answer
$90^\circ$
#11
Of what material are optical flats typically made?
  1. Plastic
  2. Quartz
  3. Glass
  4. Steel
Show answer
Glass
#12
Two pairs of cylindrical pins have been used to measure the taper of a profile gauge. Each pair is having diameter of $D_1 = 30$ mm and $D_2 = 50$ mm. The dimensions $M_1 = 55$ mm and $M_2 = 100$ mm are measured using a height gauge (as shown in the figure). The value of taper angle $\theta$ is close to: Ball of diameter $D_2$ M₂ M₁ O₂ O₁ Ball of diameter D₁ Reference surface θ
  1. 32 degrees
  2. 56 degrees
  3. 25 degrees
  4. 48 degrees
Show answer
25 degrees
#13
The least count of a vernier caliper is defined as:
  1. Sum of main scale division and vernier scale division
  2. Product of main scale division and vernier scale division
  3. Ratio of a main scale division and a vernier scale division
  4. Difference between main scale division and vernier scale division
Show answer
Difference between main scale division and vernier scale division
#14
A 4-stroke 4-cylinder reciprocating engine has a cylinder diameter of 4 cm, stroke length of 7 cm and clearance volume of 2 cm³. The engine capacity in cc is:
  1. 110
  2. 352
  3. 400
  4. 252
Show answer
252
#15
Water in a bucket is whirled in a vertical circle with a string attached to it. The water does NOT fall even when the bucket is inverted at the top of its path. This is due to:
  1. $mg$ is NOT greater than $\frac{mv^2}{r}$
  2. $mg$ is NOT less than $\frac{mv^2}{r}$
  3. $mg = \frac{mv^2}{r}$
  4. $mg$ is greater than $\frac{mv^2}{r}$
Show answer
$mg$ is NOT greater than $\frac{mv^2}{r}$
#16
To stop a car in shortest distance on a horizontal road, one should:
  1. None of the above
  2. Shut the engine off and NOT apply brakes.
  3. Apply the brakes hard enough to just prevent slipping.
  4. Apply the brakes very hard so that the wheels stop rotating.
Show answer
Apply the brakes hard enough to just prevent slipping.
#17
Among the following factors, which one does NOT influence the buckling load:
  1. Area moment of inertia
  2. Modulus of elasticity
  3. Cross-sectional area
  4. Slenderness ratio
Show answer
Cross-sectional area
#18
For the velocity profile, $\frac{u}{U_{\infty}} = \left\{\frac{y}{\delta}\right\}^{\frac{1}{5}}$ the momentum boundary layer thickness (in mm) when $\delta = 1$mm, is
  1. $\frac{5}{42}$
  2. $\frac{42}{5}$
  3. $\frac{5}{13}$
  4. $\frac{13}{5}$
Show answer
$\frac{5}{42}$
#19
The difference in pressure (in N/m²) across an air bubble of diameter 0.002 m immersed in water (surface tension = 0.072N/m) is
  1. 244
  2. 576
  3. 288
  4. 144
Show answer
288
#20
Weber's number is defined as:
  1. Square root of ratio of surface tension force to pressure force
  2. Square root of ratio of inertia force to surface tension force.
  3. Square root of ratio of inertia force to pressure force
  4. Square root of ratio of surface tension force to inertia force
Show answer
Square root of ratio of inertia force to surface tension force.
#21
Consider a laminar flow over a flat plate of length L=1m. The boundary layer thickness at the end of the plate is $\delta_w$ for water, and $\delta_a$ for air for the same freestream velocity. If the kinematic viscosities of water and air are $1 \times 10^{-6}$m²/s and $1.6 \times 10^{-5}$m²/s, respectively, the ratio of $\frac{\delta_w}{\delta_a}$ is:
  1. 1/4
  2. 1/2
  3. 4
  4. 2
Show answer
1/4
#22
The of thermodynamics states that, it is impossible to construct a device which, operating in a cycle, will produce no effect other than the transfer of heat from a cooler to a hotter body.
  1. Second law (Kelvin-Plank statement)
  2. Zeroth law
  3. First law
  4. Second law (Clausius statement)
Show answer
Second law (Clausius statement)
#23
A perfect engine works on the Carnot cycle between 727 °C and 127 °C. The efficiency of the engine is:
  1. 50%
  2. 70%
  3. 60%
  4. 40%
Show answer
60%
#24
The air standard efficiency of the Otto cycle is:
  1. $\eta=1-\frac{1}{r^{r-1}}$
  2. $\eta=1-\frac{1}{r^{\frac{r-1}{r}}}$
  3. $\eta=1-r^{\frac{r-1}{r}}$
  4. $\eta=1-r^{-1}$
Show answer
$\eta=1-\frac{1}{r^{\frac{r-1}{r}}}$
#25
A diesel engine has a compression ratio of 16 and cut-off takes place at 6% of the stroke. What will be the cut-off ratio?
  1. 9
  2. 4
  3. 1
  4. 6
Show answer
9
#26
Latent heat of is the heat energy required to change 1 kg of a liquid to gas at atmospheric pressure at its boiling point.
  1. Fusion
  2. Vaporization
  3. Condensation
  4. Fission
Show answer
Vaporization
#27
In statistical quality control, the expected process variation (natural tolerance) is commonly taken to be:
  1. None of the above
  2. $\mu \pm 2\sigma$
  3. $\mu \pm 3\sigma$
  4. $\mu \pm \sigma$
Show answer
$\mu \pm 3\sigma$
#28
By which of the following command one can draw a rectangle in AutoCAD?
  1. POL
  2. ARC
  3. REC
  4. CO
Show answer
REC
#29
In modern CNC machine tools, the backlash has been eliminated by
  1. Preloaded ball screws
  2. Ratchet and pinion
  3. Rack and pinion
  4. Slider crank mechanism
Show answer
Preloaded ball screws
#30
There are five jobs (namely A, B, C, D and E), each of which must go through machines M1 and M2 in the order M1 – M2. Processing Time (in hours) are given below: Jobs Processing Time Machine 1 (M1) Machine 2 (M2) A 5 2 B 1 6 C 9 7 D 3 8 E 10 4 Determine the sequence of processing the jobs such that the total elapsed time is minimum to process all the jobs through two machines M1 and M2.
  1. B-D-C-E-A
  2. B-C-A-E-D
  3. A-B-D-E-C
  4. B-A-D-C-E
Show answer
B-A-D-C-E
#31
The velocity ratio of the belt drive is defined as
  1. The ratio of the speed of the driving pulley to the speed of the driven pulley
  2. The ratio of the speed of the driven pulley to the speed of the driving pulley
  3. The ratio of the diameter of driving pulley to the diameter of the driven pulley
  4. The ratio of RPM of driven pulley to the RPM of the driving pulley.
Show answer
The ratio of the speed of the driving pulley to the speed of the driven pulley
#32
In case of square key, the compressive stress induced due to transmitted torque is
  1. Is equal to thrice the shear stress
  2. Is equal to four times the shear stress
  3. None of the above
  4. Is equal to twice the shear stress
Show answer
Is equal to twice the shear stress
#33
Which of the following is correct
  1. Coupling and clutch are the same
  2. Shafts connected by coupling have non-collinear axes
  3. Clutch can connect or disconnect two shafts
  4. Coupling can connect or disconnect two shafts
Show answer
Clutch can connect or disconnect two shafts
#34
A mass of 1 kg is attached to the end of a spring with a stiffness 0.7 N/mm. The critical damping coefficient of this system will be
  1. 92Ns/m
  2. 522Ns/m
  3. 40 Ns/m
  4. 2Ns/m
Show answer
522Ns/m
#35
Mohr's circle model is used to compute
  1. State of material property at any point
  2. State of temperature at any point
  3. State of stress at a point
  4. None of the above
Show answer
State of stress at a point
#36
Which of the following is correct
  1. Poisson ratio = Longitudinal strain x Lateral strain
  2. Poisson ratio = Longitudinal strain / Lateral strain
  3. Lateral strain = Poisson ratio x Longitudinal strain
  4. Longitudinal strain = Poisson ratio x Lateral strain
Show answer
Lateral strain = Poisson ratio x Longitudinal strain
#37
The cross-sectional area of a rectangular bar is 10000mm² and it is subjected to an axial load of 20kN. What is the normal stress on a section inclined at an angle of 30° with normal cross-section of the bar?
  1. 5 N/mm²
  2. 966 N/mm²
  3. 866 N/mm²
  4. 5 N/mm²
Show answer
866 N/mm²
#38
In an adiabatic process, which of the following in not true?
  1. The temperature of the gas changes
  2. Heat enters or leaves the gas
  3. No heat enters or leaves the gas
  4. The change in internal energy is equal to the mechanical work done
Show answer
Heat enters or leaves the gas
#39
If the value of n = 0 in the equation pv" = C, then the process is called
  1. Constant pressure process
  2. Isothermal process
  3. Constant volume process
  4. Adiabatic process
Show answer
Constant pressure process
#40
A good refrigerant must have specific heat when it is vaporized
  1. Low, high
  2. High, high
  3. High, low
  4. Low, low
Show answer
Low, high
#41
The mass of water vapour present in the unit volume of dry air is
  1. Specific humidity
  2. Degree of saturation
  3. Relative humidity
  4. Absolute humidity
Show answer
Absolute humidity
#42
Helmholtz function is
  1. g = h - Ts
  2. dh = Tds + vdP
  3. a = u - Ts
  4. du = Tds - Pdv
Show answer
a = u - Ts
#43
For a flow over a flat plate,
  1. The boundary layer thickness (8) is equal to the length of the flat plate
  2. The boundary layer thickness (8) is much smaller than the length of the flat plate
  3. The boundary layer thickness (8) is greater than the length of the flat plate
  4. None of the above
Show answer
The boundary layer thickness (8) is much smaller than the length of the flat plate
#44
If the flow is irrotation which of the following need to be satisfied.
  1. $V.\nabla \vec{v} = 0$
  2. $\nabla \times \vec{v} = 0$
  3. $\nabla.\vec{v} = 0$
  4. None of the above
Show answer
$\nabla \times \vec{v} = 0$
#45
What will be the velocity distribution or profile when a fluid is filled between two parallel plates (top and bottom) in which the top plate is moving with a constant velocity V and the bottom plate is fixed.
  1. Velocity distribution is zero
  2. Velocity distribution is linear
  3. There is uniform distribution of the fluid
  4. Velocity distribution is parabolic
Show answer
Velocity distribution is linear
#46
When a material is able to resist fracture due to high impact load is called
  1. Hardness
  2. Plasticity
  3. Toughness
  4. Stiffness
Show answer
Toughness
#47
In single V-butts welds, the angle between edges is
  1. 50° to 60°
  2. 40° to 50°
  3. 60° to 70°
  4. 70° to 90°
Show answer
60° to 70°
#48
In diamond, the nature of the atomic bond
  1. Covalent
  2. Ionic
  3. Metallic
  4. None of the above
Show answer
Covalent
#49
The pattern used in investment casting is
  1. Clay
  2. Metal
  3. Wax
  4. Wood
Show answer
Wax
#50
While using the disposable pattern, the metal should be poured
  1. At the same rate as for other casting process
  2. Very rapidly
  3. Very slowly
  4. At any rate
Show answer
Very rapidly
#51
The dimension of bore 14.67mm in a workpiece is measured using
  1. Micrometer
  2. Pneumatic gauge
  3. Plug gauge
  4. Steel rule
Show answer
Plug gauge
#52
Autocollimator is used for
  1. Parallelism measurement
  2. Flatness measurement
  3. Straightness measurement
  4. Angular measurement
Show answer
Angular measurement
#53
Which of the following is not correct with respect to two stroke engine
  1. Frictional losses are less
  2. Two stroke engine has high maintenance cost
  3. A two stroke engine is easily reversed
  4. A two stroke engine occupies less space
Show answer
Frictional losses are less
#54
The thermal efficiency of petrol engines is
  1. Lower due to lower compression ratio
  2. Lower due to higher compression ratio
  3. Higher due to higher compression ratio
  4. Higher due to lower compression ratio
Show answer
Lower due to lower compression ratio
#55
The word automation leads to
  1. Machine controlled by workers
  2. Assisting and replacing humans by machines
  3. All of these
  4. Increase in production
Show answer
All of these
#56
In a static environment, forecasting future is
  1. Long term forecasting
  2. Passive forecasting
  3. Short term forecasting
  4. Active forecasting
Show answer
Passive forecasting
#57
Time taken for the job from its arrival to the system until its departure is
  1. Completion time
  2. Due time
  3. Flow time
  4. Processing time
Show answer
Flow time
#58
The C items representing the ABC analysis are those which represents
  1. Small percentage of closing inventory value
  2. High percentage of closing inventory value
  3. Small percentage of the total annual consumption value
  4. High percentage of the total annual consumption value
Show answer
Small percentage of the total annual consumption value
#59
When the ordering cost is increased to 4 times, the economic order quantity(EOQ) will be increased to
  1. Remains the same.
  2. 2 times
  3. 3 times
  4. 8 times
Show answer
2 times
#60
Consider the following statements: The form factor of a spur gear tooth depends upon the 1. Number of teeth 2. Pressure angle 3. Addendum modification coefficient 4. Circular pitch. Of these statements
  1. 1 and 3 are correct
  2. 2 and 4 are correct
  3. 1, 2 and 3 are correct
  4. 1 and 4 are correct
Show answer
1, 2 and 3 are correct
#61
A machine element XY, fixed at end X, is subjected to an axial load P, transverse load F, and a twisting moment T at its free end Y. The most critical point from the strength point of view is F T Y X
  1. A point on the circumference at location Y
  2. A point at the center at location X
  3. A point on the circumference at location X
  4. A point at the center at location Y
Show answer
A point on the circumference at location Y
#62
Heat and work are
  1. Point functions
  2. Extensive properties
  3. Intensive properties
  4. Path functions
Show answer
Path functions
#63
In a Rankine cycle, the enthalpies at turbine entry and outlet are 3159kJ/kg and 2187 kJ/kg, respectively. If the specific pump work is 2kJ/kg the specific steam consumption (in kg/kWh) of the cycle based on net output is
  1. 2
  2. 71
  3. 5
  4. 1
Show answer
71
#64
Consider the following statement regarding refrigerants: 1. Refrigerant NH, is used in reciprocating compressors 2. Refrigerant CO, is used in reciprocating compressors 3. Refrigerant R-11 is used in centrifugal compressors Which of this statement is/are correct?
  1. 2 and 4
  2. 1,2 and 3
  3. 1 and 2
  4. 1 and 3
Show answer
1 and 3
#65
Match List-I (Process) with List-II (characteristics) and select the correct answer using the code given below List-I P. Throttling process Q. Isentropic process R. Free expansion S. Isothermal process
  1. P-III, Q-II, R-IV, S-I
  2. P-IV, Q-II, R-I, S -III
  3. P-III, Q-I, R-IV, S-II
  4. P-IV, Q-I, R-II, S-III
Show answer
P-III, Q-II, R-IV, S-I
#66
According to Bernoulli's equation for steady ideal fluid flow
  1. Velocity and pressure are inversely proportional
  2. Principle of conservation mass holds
  3. None of these
  4. The energy is constant along the streamline but may vary across stream lines
Show answer
The energy is constant along the streamline but may vary across stream lines
#67
The total pressure on a horizontally immersed surface (of surface area A) with its centre of gravity at a depth $\bar{x}$ from liquid surface in a liquid of specific weight $\omega$ is
  1. $\omega A \bar{x}$
  2. $\omega A$
  3. $\frac{\omega A}{\bar{x}}$
  4. $\omega \bar{x}$
Show answer
$\omega A \bar{x}$
#68
Match List-I with List-II and select the correct answer using the codes given below List-I List-II P. Propeller 1. Inward flow reaction Q. Francis turbine 2. Tangential flow impulse R. Kaplan turbine 3. Axial flow reaction with fixed vanes S. Pelton turbine 4. Axial flow reaction with adjustable vanes
  1. P-3, Q-4, R-1, S-2
  2. P-2, Q-1, R-4, S-3
  3. P-2, Q-4, R-1, S-3
  4. P-3, Q-1, R-4, S-2
Show answer
P-2, Q-1, R-4, S-3
#69
Consider the following assumptions: 1. The fluid is compressible. 2. The fluid is inviscid. 3. The fluid is incompressible and homogeneous. 4. The fluid is viscous and compressible. The Euler's equation of motion requires assumptions indicated in
  1. 3 and 4
  2. 2 and 3
  3. 1 and 2
  4. 1 and 4
Show answer
2 and 3
#70
The crystal structure of austenite is
  1. Hexagonal Closed Packed
  2. Face Centred Cubic
  3. BCC
  4. Body Centred Tetragonal
Show answer
Face Centred Cubic
#71
Match the casting defects (Group A) with the probable causes (Group B) Group A Group B 1. Cold Shut P. Wide range of solidification temperature 2. Shrinkage Q. Low permeability of the sand mould 3. Blow holes R. Volumetric contraction both in liquid and solid stage 4. Hot tears S. Improper fusion of two streams of liquid metal
  1. 1-S, 3-Q, 2-R, 4-P,
  2. 3-S, 1-Q, 2-R, 4-P,
  3. 4-S, 2-Q, 1-R, 3-P,
  4. 4-S, 3-Q, 2-R, 1-P,
Show answer
1-S, 3-Q, 2-R, 4-P,
#72
Match the following products with preferred manufacturing processes: Group A (Products) Group B (Manufacturing Processes) I. Rails P. Blow molding II. Engine crankshaft Q. Extrusion III. Aluminium channels R. Forging IV. PET water bottles S. Rolling
  1. I-S, II-R, III-P, IV-Q
  2. I-Q, II-S, III-R, IV-P
  3. I-S, II-R, III-Q, IV-P
  4. I-R, II-S, III-Q, IV-P
Show answer
I-S, II-R, III-Q, IV-P
#73
Consider the following statements. P) Electrolyte is used in Electro-chemical machining. Q) Electrolyte is used in Electrical discharge machining. R) Abrasive-slurry is used in Ultrasonic machining. S) Abrasive-slurry is used in Abrasive jet machining. Among the above statements, the correct ones are
  1. P and Q only
  2. Q and S only
  3. Q, R and S only
  4. P and R only
Show answer
Q, R and S only
#74
A gating ratio 1 : 2 : 4 is used to design the gating system for magnesium alloy casting. This gating system refer to the cross-section areas of the various gating elements as given below: 1. Down sprue 2. Runner bar 3. Ingate The correct sequence of the above elements in the ration 1 : 2 : 4 is
  1. 1, 3 and 2
  2. 1, 2 and 3
  3. 3, 1 and 2
  4. 2, 3 and 1
Show answer
1, 2 and 3
#75
Match the correct pairs between List-I and List-II Measuring Instruments Applications P. Talysurf 1. T-slot Q. Telescopic gauge 2. Flatness R. Transfer callipers 3. Internal diameter S. Autocollimator 4. Roughness
  1. P-4, Q-3, R-1, S-2
  2. P-2, Q-3, R-4, S-1
  3. P-2, Q-3, R-1, S-4
  4. P-3, Q-2, R-1, S-4
Show answer
P-4, Q-3, R-1, S-2
#76
The component that is responsible for converting the rotation of the steering wheel into lateral motion is the
  1. Steering wheel
  2. Tie rod
  3. Steering shaft
  4. Steering gearbox
Show answer
Tie rod
#77
In a Morse test for a 2-cylinder, 2-stroke, spark ignition engine, the brake power was 9 kW whereas the brake powers of individual cylinders with spark cut off were 4.25 kW and 3.75 kW respectively. The mechanical efficiency of the engine is
  1. 5%
  2. 90%
  3. 5%
  4. 80%
Show answer
90%
#78
Knocking in a spark ignition engine can be reduced by 1. Retarding the spark 2. Supercharging 3. Increasing the engine speed 4. Using a fuel of long straight chain structure Select the correct answer using the codes given below
  1. 1 and 4
  2. 2 and 3
  3. 2 and 4
  4. 1 and 3
Show answer
1 and 4
#79
NC contouring is an example of following positioning
  1. Point-to- path
  2. Incremental
  3. Continuous path
  4. Absolute
Show answer
Continuous path
#80
Consider the following statements. P. Computer aided process planning (CAPP) takes input from material requirement plan (MRP). Q. Production flow analysis helps in work cell formation. R. Group technology takes input from choice of machining or cutting parameters. Among the above statements, the correct one(s) is (are)
  1. Q only
  2. P only
  3. Q and R only
  4. P and R only
Show answer
Q only
#81
Match the geometric tolerances with their correct symbols: P. Perpendicularity 1. O Q. Flatness 2. T R. Concentricity 3. O S. Roundness (Circularity) 4. O
  1. P-2, Q-3, R-4, S-1
  2. P-3, Q-1, R-4, S-2
  3. P-2, Q-3, R-1, S-4
  4. P-3, Q-2, R-1, S-4
Show answer
P-3, Q-1, R-4, S-2
#82
Statistical quality control was developed by
  1. Walter A. Shewhart
  2. W. E. Deming
  3. George Dantzig
  4. Frederick Tylor
Show answer
Walter A. Shewhart
#83
Which of the following elements transfers torque and is only subjected with the bending moment?
  1. Clutch
  2. Brake
  3. Axle
  4. Belt drive
Show answer
Axle
#84
Which is not a possible type of failure in a riveted joint?
  1. Shear failure of rivet
  2. Shear failure of plate
  3. Tensile failure of the plate between rivets
  4. Crushing failure of the plate
Show answer
Shear failure of plate
#85
Which of the following correctly symbolizes a fillet joint?
  1. A right angled triangle
  2. A triangle
  3. Two parallel lines with an arc above them
  4. A triangle with an arc above it
Show answer
A triangle with an arc above it
#86
Which of the following is a type of Engineering Materials and is a Metal?
  1. Both B and C
  2. Non-Ferrous Metals
  3. Ferrous Metals
  4. Asbestos
Show answer
Both B and C
#87
Which of the following is an example of a thermoplastic?
  1. Epoxide
  2. Urethane
  3. Acetal
  4. Melamine
Show answer
Acetal
#88
On average, what is the maximum use temperature of engineering ceramics?
  1. 2760°C
  2. 2860°C
  3. 6815°C
  4. 3400°C
Show answer
2760°C
#89
How is the creep strength of ceramics when compared to other materials?
  1. Zero
  2. High
  3. Excellent
  4. Low
Show answer
High
#90
What is the mathematical expression of the first law of thermodynamics for a closed system?
  1. $\Delta U = Q + W$
  2. $Q = W - \Delta U$
  3. $Q = U + W$
  4. $\Delta U = Q - W$
Show answer
$\Delta U = Q - W$
#91
The Brayton cycle is commonly used in:
  1. Gas turbines
  2. Diesel engines
  3. Refrigeration systems
  4. Steam power plants
Show answer
Gas turbines
#92
Which statement accurately describes the Carnot refrigeration cycle?
  1. It is a reversible cycle that operates between two temperature reservoirs
  2. It is most efficient when operating with a high-temperature reservoir only
  3. It has a higher COP than other refrigeration cycles
  4. It operates with a single-phase working fluid
Show answer
It is a reversible cycle that operates between two temperature reservoirs
#93
The Kelvin-Planck statement of the second law of thermodynamics states that:
  1. Energy cannot be created or destroyed
  2. The entropy of a closed system cannot decrease
  3. Heat flows spontaneously from hot to cold
  4. All processes tend towards equilibrium
Show answer
The entropy of a closed system cannot decrease
#94
The purpose of the condenser in a Rankine cycle is to:
  1. Superheat the steam before entering the turbine
  2. Convert the steam to a liquid state
  3. Increase the temperature of the working fluid
  4. Increase the pressure of the working fluid
Show answer
Convert the steam to a liquid state
#95
The term "relative humidity" refers to:
  1. The ratio of the partial pressure of water vapor to the saturation pressure
  2. The ratio of the dew point temperature to the wet-bulb temperature
  3. The ratio of the wet-bulb temperature to the dry-bulb temperature
  4. The ratio of the specific humidity to the dry-bulb temperature
Show answer
The ratio of the partial pressure of water vapor to the saturation pressure
#96
A fluid is considered incompressible if its:
  1. Surface tension is negligible
  2. Temperature is low
  3. Density is constant
  4. Viscosity is high
Show answer
Density is constant
#97
The Reynolds number is used to determine the flow regime in a fluid based on the relationship between:
  1. Viscosity and density
  2. Velocity and pressure
  3. Inertia and viscosity
  4. Surface tension and temperature
Show answer
Inertia and viscosity
#98
The Venturi meter is based on the principle of:
  1. Pressure difference in a constriction
  2. Temperature change in a converging-diverging duct
  3. Density change in a narrowing pipe
  4. Viscosity measurement
Show answer
Pressure difference in a constriction
#99
A hydraulic turbine converts:
  1. Pressure energy into kinetic energy
  2. Mechanical energy into potential energy
  3. Kinetic energy into pressure energy
  4. Kinetic energy into mechanical energy
Show answer
Kinetic energy into mechanical energy
#100
A fluid that has a constant viscosity but changes its density is classified as:
  1. Incompressible fluid
  2. Non-Newtonian fluid
  3. Compressible fluid
  4. Newtonian fluid
Show answer
Compressible fluid
#101
TIG welding stands for:
  1. Theoretical Inverse Gas
  2. Thermal Inductive Gas
  3. Torch Ignition Gas
  4. Tungsten Inert Gas
Show answer
Tungsten Inert Gas
#102
The material removed during machining is called:
  1. Slag
  2. Slug
  3. Swarf
  4. Swage
Show answer
Swarf
#103
Milling involves cutting material using:
  1. A rotating tool with multiple edges
  2. A rotating tool with a single edge
  3. A stationary tool and a rotating workpiece
  4. A reciprocating tool
Show answer
A rotating tool with multiple edges
#104
The term "grain boundary" refers to the boundary between:
  1. Two different types of lattices
  2. Individual atoms within a lattice
  3. Two different crystal structures
  4. Adjacent crystalline grains
Show answer
Adjacent crystalline grains
#105
A common defect in casting caused by improper mold compaction is called:
  1. Porosity
  2. Shrinkage
  3. Hot tear
  4. Blowhole
Show answer
Blowhole
#106
A milling cutter with teeth on its periphery and face is called a:
  1. End mill
  2. Ball mill
  3. Fly cutter
  4. Slot mill
Show answer
End mill
#107
An automobile designed for transporting goods is classified as a:
  1. Coupe
  2. Hatchback
  3. Van
  4. Sedan
Show answer
Van
#108
The term "compression ratio" in an engine refers to the ratio of the:
  1. Air-fuel mixture to exhaust gases
  2. Engine's displacement to its weight
  3. Power output to the engine's weight
  4. Volume of the combustion chamber at bottom dead center to top dead center
Show answer
Volume of the combustion chamber at bottom dead center to top dead center
#109
A profilometer is a tool used to measure:
  1. Temperature
  2. Angle
  3. Length
  4. Surface roughness
Show answer
Surface roughness
#110
The device that ensures power is evenly distributed to the wheels while turning in an automobile is the:
  1. Differential
  2. Transmission
  3. Steering wheel
  4. Brake pedal
Show answer
Differential
#111
CAM refers to:
  1. Controlled Algorithmic Management
  2. Computer-Aided Maintenance
  3. Centralized Analysis and Manufacturing
  4. Computer-Aided Manufacturing
Show answer
Computer-Aided Manufacturing
#112
According to the instructions, what is the penalty for a wrong answer in the objective type questions?
  1. 1/4 of the marks assigned to the question will be deducted.
  2. 1/2 of the marks assigned to the question will be deducted.
  3. The question will be disregarded.
  4. No penalty will be applied.
Show answer
1/4 of the marks assigned to the question will be deducted.
#113
What is the maximum number of items (questions) in this test booklet?
  1. 120
  2. 150
  3. 100
  4. 200
Show answer
120
#114
What is the time allowed for the examination?
  1. 1 Hour
  2. 4 Hours
  3. 3 Hours
  4. 2 Hours
Show answer
2 Hours
#115
What is the maximum marks for the examination?
  1. 200
  2. 150
  3. 100
  4. 120
Show answer
120
#116
According to instruction 7, what should a candidate hand over to the Invigilator after the examination concludes?
  1. Only the Answer/Response Sheet
  2. The Test Booklet and Candidate's Copy of the Response Sheet
  3. The Candidate's Copy of the Response Sheet only
  4. The Test Booklet only
Show answer
Only the Answer/Response Sheet
#117
What is the penalty for giving more than one answer to a question?
  1. It will be treated as a wrong answer with a penalty of 1/4 of the marks.
  2. No penalty, one of the answers will be considered correct.
  3. The question will be marked as correct.
  4. The candidate will be disqualified.
Show answer
It will be treated as a wrong answer with a penalty of 1/4 of the marks.
#118
What is the penalty for leaving a question blank?
  1. No penalty will be applied.
  2. 1/4 of the marks assigned to the question will be deducted.
  3. 1/2 of the marks assigned to the question will be deducted.
  4. The question will be marked as incorrect.
Show answer
No penalty will be applied.
#119
Which type of pen should be used for writing the Centre Code and Roll Number on the Answer Sheet?
  1. Pencil
  2. Blue Ball Point Pen
  3. Black Ball Point Pen
  4. Any color Ball Point Pen
Show answer
Any color Ball Point Pen
#120
How is the modulus of rigidity defined?
  1. The ratio of shear stress to shear strain within elastic limit.
  2. The ratio of identical stresses acting in three mutually perpendicular directions on a body to the volumetric strain
  3. The ratio of linear stress to liner strain within elastic limit
  4. The ratio of linear stress to lateral strain within elastic limit
Show answer
The ratio of shear stress to shear strain within elastic limit.
#121
Which of the following steps in lean manufacturing is related to 'Shitsuke'?
  1. Shitsuke (Sustain)
  2. Seiri (Sort)
  3. Seiketsu (Standardize)
  4. Seiso (Shine)
Show answer
Shitsuke (Sustain)
#122
Arrange the following steps in order to eliminate waste and enhance efficiency in lean manufacturing.
  1. Seiton, Seiketsu, Shitsuke, Seiri, Seiso
  2. Seiri, Seiton, Seiso, Shitsuke, Seiketsu
  3. Seiri, Seiso, Seiketsu, Shitsuke, Seiton
  4. Seiri, Seiton, Seiso, Seiketsu, Shitsuke
Show answer
Seiri, Seiton, Seiso, Shitsuke, Seiketsu
#123
Match the gear types to their applications: Spur gears
  1. For intersecting axes shafts
  2. For non-parallel and non-intersecting axes shafts
  3. For both parallel and non-parallel and non-intersecting axes shafts
  4. For parallel axes shafts
Show answer
For parallel axes shafts
#124
Match the gear types to their applications: Helical gears
  1. For both parallel and non-parallel and non-intersecting axes shafts
  2. For parallel axes shafts
  3. For intersecting axes shafts
  4. For non-parallel and non-intersecting axes shafts
Show answer
For both parallel and non-parallel and non-intersecting axes shafts
#125
Match the gear types to their applications: Spiral gears
  1. For parallel axes shafts
  2. For both parallel and non-parallel and non-intersecting axes shafts
  3. For intersecting axes shafts
  4. For non-parallel and non-intersecting axes shafts
Show answer
For non-parallel and non-intersecting axes shafts
#126
Match the gear types to their applications: Bevel gears
  1. For parallel axes shafts
  2. For intersecting axes shafts
  3. For non-parallel and non-intersecting axes shafts
  4. For both parallel and non-parallel and non-intersecting axes shafts
Show answer
For intersecting axes shafts
#127
Which of the following is NOT a characteristic of an adiabatic process?
  1. Constant enthalpy
  2. No work done
  3. No change in entropy
  4. Constant internal energy
Show answer
No work done
#128
In thermodynamics, what is a characteristic of an isochoric process?
  1. Constant enthalpy
  2. No change in entropy
  3. Constant internal energy
  4. No work done
Show answer
Constant internal energy
#129
What is a characteristic of an isothermal process?
  1. No work done
  2. Constant internal energy
  3. Constant enthalpy
  4. No change in entropy
Show answer
Constant enthalpy
#130
Which of the following is a characteristic of an isentropic process?
  1. Constant enthalpy
  2. Constant internal energy
  3. No work done
  4. No change in entropy
Show answer
No change in entropy
Play in QuizPilot